Saddleback Plumbing Heating & Air Blog: Posts Tagged ‘Heating’

Basic Furnace Safety Tips

Friday, January 20th, 2012

While you should schedule a yearly maintenance visit with a qualified HVAC technician to check for any safety concerns, you can also reduce potential safety hazards in the heating system of your Dana Point home. Whether you have a furnace or a heat pump, you can substantially decrease the chances of dangerous situations with a few minor routine tasks.

If you have any questions about how to better maintain your heating system, give us a call to speak with one of our expert HVAC technicians. Here are a few guidelines to get you started.

Ventilation in Forced-air Systems:

  • Regularly vacuum and clean out your heating vents and fan blower.
  • Check the condition of your chimney and vent pipe to make sure that none of the parts are damaged or show signs of deterioration.
  • Test the thermostat occasionally to make sure your heating system is working at optimal levels. There could be a safety concern if your heater is not properly heating your home.

Heat Exchangers:

  • Heat exchangers should be inspected often to prevent carbon monoxide leaks. Check for any obvious issues, such as rust or other damages.
  • The heat exchanger for furnaces should be inspected by a professional once a year in case there are hidden problems with the equipment, or if any of the components need to be replaced.
  • Check the pilot light in gas furnaces for any flickers or changes in color. Have someone turn up the thermostat while you watch the light, but turn off the system for five minutes first. If there are any changes, there could be a problem with the heat exchanger. Call a professional if you suspect issues with your heat exchanger.

Heating Equipment Inspections and Adjustments:

  • Adjust the temperature settings if you suspect that the heater isn’t working properly, and if it doesn’t work call a professional heating technician, or if you aren’t sure how to locate or adjust the controls.
  • Check the overall equipment for cracks, rust, or any other obvious signs of damage or deterioration that could create safety hazards.

In addition to performing these tasks, call a licensed Dana Point heating contractor to inspect your heating system at least once a year.

Continue Reading

Tags: , , , , ,
Posted in Services | Comments Off on Basic Furnace Safety Tips

Woodbridge Heating Guide: Furnace Fan Limit Switch

Friday, January 13th, 2012

When researching your Woodbridge furnace and potential problems it might have, you’ve probably run across a few references to the fan limit switch. And while you know that it can break in a number of ways, do you know what the switch does and what you should look for when checking your furnace its air handler for problems?

What the Limit Switch Does

To put it very simply, the furnace fan limit switch is a control that tells your furnace’s fan when to turn on and off. So, when the furnace isn’t on, it tells the blower not to operate (and send cold air into your home) and when the furnace is on, it tells the blower to turn on and start circulating the warm air.

While the primary function of the limit switch is to turn the blower fan on and off, it also has a safety role. When the temperature in the air supply plenum gets too hot, the limit switch turns off the furnace boiler to keep there from being any damage from overheating. This is handy if there is a blockage in the air vents or the controls are messed up due to water damage or improper adjustments to the settings.

Looking for Problems

Most of the time, when there is an issue with your furnace turning off or on frequently, the limit switch is one of the first things you will check. Because the switch is electronic and is attached to a thermostat which measures temperature in the air supply plenum, a small problem can result in it not working properly. So, you can easily check it by temporarily bypassing the switch and seeing if your device turns on or off properly.

In many cases, if the limit switch is the problem, you will still need to call a Woodbridge professional for replacement, but you can avoid a lot of headaches related to tracking down the source of the problem. If you suspect a limit switch problem, make sure to call someone immediately, because it does provide an important safety function and because without it your furnace won’t cycle on and off properly.

Continue Reading

Tags: , , , , , ,
Posted in Services | Comments Off on Woodbridge Heating Guide: Furnace Fan Limit Switch

High Efficiency Northwood Furnaces: Chimney Concerns

Wednesday, January 11th, 2012

When upgrading to a high efficiency gas furnace in Northwood, you may need to make some upgrades to your chimney. Older chimneys built for standard furnaces with normal exhaust needs are not built to the specifications needed by today’s high efficiency models. Not only is it unsafe to leave it as is, but the cost of repairs if you don’t have it upgraded can be substantial.

Down-Sizing

A common concern when upgrading to a high efficiency gas furnace is the issue of condensation and draft. Because the amount of exhaust being vented is reduced by a high efficiency furnace, your current setup is not sufficient for the new model. So, it needs to be reduced in size by a professional to avoid backup of exhaust. Proper chimney sizing is a complex process that requires professional guidelines and careful measurements of all appliances in your home.

Because the chimney often isn’t used at all for a high efficiency furnace (often PVC pipe used instead), the extra airflow in the chimney can become a major issue.

Chimney Condensation

The biggest concern for the chimney when changing the furnace efficiency is condensation. Specifically, acidic condensation droplets can build up in the chimney if not properly stopped. A new chimney liner must be placed in the chimney to avoid excessive corrosion due to the acid droplets. Keep in mind that the efficiency of your new furnace will determine whether you will use the traditional chimney for exhaust or if a new line will be installed to vent your furnace.

When to Take Action

If you have your furnace replaced, your Northwood technician will likely discuss the chimney situation in your home with you. Keep in mind that this might be necessary and that there might be an added cost involved because of it. Modern furnaces are not designed to accommodate aging chimneys and your safety and the integrity of your house are at risk if you don’t retrofit the chimney if necessary.

Continue Reading

Tags: , , , , ,
Posted in Services | Comments Off on High Efficiency Northwood Furnaces: Chimney Concerns

Furnace Tip 1: How to Fix a Faulty Furnace Blower

Monday, January 9th, 2012

The blower fan on your furnace is designed to distribute warm air through the ductwork in your Talega home evenly, ensuring you use all of the energy consumed by your furnace. If the blower doesn’t turn on when the furnace turns on or it continues to run when the furnace is off, it can cost you money and result in cold rooms. Here are some tips on how to fix a faulty furnace blower.

What is the Problem?

First, check to see what the problem is. If your furnace blower remains on all of the time, it may be a thermostat issue. Make sure the fan isn’t set to stay on continuously (a common setting for most air handlers). You should also check the limit control switch to make sure it is working properly. If this is broken, it needs to be replaced which is a relatively simple fix.

If the furnace blower isn’t turning on at all, you may have a belt problem. This can be fixed by you if you have the proper tools. To repair the belt problem, first turn off all electricity to the device. You’ll need to remove the old furnace blower belt, so release the tension in the pulleys before removing the belt.

Installing a new belt is not unlike doing so for your car. Make sure to check the blower or your user manual for proper tension when you install the new belt. Make sure you purchase the right size belt and set it to the right tension. If you cannot or you do not feel comfortable doing so, you should call a professional to inspect and repair the problem for you.

Getting the Blower Back Up and Running

Once your new belt is in place, test the system carefully, starting with the lowest setting (if there are variable settings). If it does not yet work or if something sounds strange, call a Talega heating and air conditioning technician right away. You don’t want the motor to burn out or something else more substantial to go wrong with your furnace or air handler during the middle of the winter.

Continue Reading

Tags: , , , , , ,
Posted in Services | Comments Off on Furnace Tip 1: How to Fix a Faulty Furnace Blower

Troubleshooting Thermostat Issues: Is it the Thermostat or Something Else?

Friday, January 6th, 2012

If your room temperature is too hot or cold, what is the first thing you check? Probably the thermostat. If you are a San Clemente homeowner, you probably have played around with the setting on a thermostat, much to the chagrin of other occupants who don’t share your same comfort level. And if you try and adjust a thermostat at work – well forget about it. Most companies now have locking thermostats or “false” ones that don’t actually connect to the heating and cooling system.

So if you have a temperature problem, is it really the thermostat that causes it? Maybe yes and maybe no. One physical characteristic to check is the location of the thermostat. If it is in a drafty hallway or near a heat source, it only reads the temperature for that area and other parts of the building are neglected. You will often find more than one thermostat in a home that is tied into more than one furnace or air conditioner.

The older more popular round thermostats are manually controlled and do not adjust to any conditions in your San Clemente home. They simply control the heating and cooling functions based on a human turning a dial. It’s as simple as that. So if you use this method to adjust the temperatures, blame yourself and not the thermostat. You might want to consider installing a digital, programmable thermostat.

With that in mind, let’s look at some typical ways to troubleshoot a thermostat.

  • Check the anticipator, which is a small metal tab on the front of the printed scale. Give it a light push in either direction. It may be stuck.
  • Clean the interior of the thermostat housing and clean the contacts (small metal plates)
  • Check loose wires or wires that may be corroded.
  • Read the thermostat manual (if not available, look online) for other tips such as ensuring there is voltage to the terminals.

If you have checked everything and the thermostat seems to be in working order, look for other things within the heating & cooling system. These include blocked or restricted registers and vents, leaks or cracks in ductwork, and dirty air handling filters.

Continue Reading

Tags: , , , , , ,
Posted in Services | Comments Off on Troubleshooting Thermostat Issues: Is it the Thermostat or Something Else?

Common Garden Grove Furnace Problems

Monday, January 2nd, 2012

When it comes to your home Garden Grove furnace, you simply want it to work all of the time. But just like any other piece of equipment, your furnace will have problems from time to time. A few of these are relatively simple to fix on your own, but for the most part you’ll need to call in someone to take care of the repairs for you.

However, before you can do that, you’ll need to recognize that a problem exists at all. And the earlier you notice the warning signs, the better off you’ll be. It’s always better to get a furnace problem taken care of right away than to wait until your furnace stops working completely.

It’s also good to remember that quite often the problems you’re having with your furnace are really originating with your thermostat. This is usually welcome news, as thermostats are much cheaper and easier to repair and replace than many other parts of your furnace. In fact, even if your furnace isn’t working at all, it may only be the result of a faulty thermostat.

Another problem you may start to notice is that one part of your Garden Grove house is being warmed more than another part. When this happens, it can be a sign that there is something wrong with the furnace, but it may also be that the pressure in your duct system is not balanced properly. A simple rebalancing of this system can have your house heating evenly again in no time.

You may also realize that your furnace seems to be cycling on and off too often. When a furnace is working properly, it will come on for a considerable period of time and then shut off until the temperature in the house drops below the desired level. However, some problems can cause your furnace to complete many short cycles rather than fewer short ones.

If this is happening to your furnace, there are several possible causes. Something might be wrong with the blower on the furnace or the thermostat might not be feeding the furnace the correct information. Another possibility is that your furnace’s air filter is dirty or clogged.

While there are sometimes simple and straightforward solutions to these types of common furnace problems, it’s best to call in a Garden Grove professional to have them take a look if you’re not sure where to start searching for a problem. In most cases you’ll need them to come out and make the necessary repairs anyway.

Continue Reading

Tags: , , , , ,
Posted in Services | Comments Off on Common Garden Grove Furnace Problems

A Question from Robinson Ranch: When Should You Replace Instead of Repair Your Heating?

Wednesday, December 21st, 2011

We all dread an expensive repair in Robinson Ranch, whether it is a car that needs a new transmission, a leaky roof that needs new shingles, or electrical wiring that has been chewed up by a wild animal. We often try and put bandages on things that we know should be replaced but we just can’t afford to replace them.

The same can be said about your home’s heating system. When your heat goes out or your home just doesn’t seem to be heating up to the setting on your thermostat, your first inclination is to check and see if it is running. Some people will put their hand over a heating vent to check for hot air while others may go into the basement or mechanical room to listen to hear if the furnace is running. Maybe there is a blockage in the ventilation system or a blown circuit breaker, two relatively easy fixes.

If the furnace isn’t working after checking the obvious symptoms, your next move is to call for service. Any Robinson Ranch heating professional would be able to diagnose your problem and offer suggested repairs. Something relatively minor like a bad circuit board or blown fan motor are not real expensive repairs and are the best option versus replacing the furnace. And you may keep experiencing the same problem and getting the same repair work done – anything to avoid an expensive replacement.

But at some point the vicious cycle will come to an end. Your repair bills will begin to inch their way past the cost of replacing the furnace. You can only bandage a problem so long before it becomes “unfixable.” You may not want to pay an expensive replacement bill but consider the alternatives.

First is the obvious – it costs too much to keep repairing the furnace. Secondly, you never know when the furnace may break down and its failure to operate could have dangerous effects on the people in your home, especially if someone is sick. Third, your furnace may not be able to keep up with the heating demand due to lifestyle changes, i.e. an addition put on the house, carpeting removed and wood floors exposed, a new window, door, or skylight added, etc. Your old furnace may not have been designed to keep up with these changes and the repairs are only delaying the inevitable.

Ask yourself if everyone in your Robinson Ranch home is comfortable during cold weather. If most answer no, it may be time to consider replacing that old furnace with a new, energy efficient model that uses today’s technology – and leaves a smaller carbon footprint – to keep up with the demand for heat, in any sized building or home. Your decision to replace your old heating system could be as simple as the need to use modern technology to solve your indoor comfort problems.

Continue Reading

Tags: , , , , ,
Posted in Services | Comments Off on A Question from Robinson Ranch: When Should You Replace Instead of Repair Your Heating?

Space Heating vs. an Upgrade to Your Fountain Valley Heating System

Wednesday, December 14th, 2011

If your Fountain Valley home’s heating system isn’t really cutting it anymore, it may be time to take a step back and consider what your options are. After all, upgrading to an entirely new heating system is a big investment and a large project that will likely disrupt your life at least for a short period of time. However, under certain circumstances it’s the best alternative out there.

One option to consider when you’re unhappy with your home heating situation is supplementing your central heating system with space heaters. These are generally inexpensive and can be placed virtually anywhere in your house or taken with you from one room to another.

Especially if there is a small part of your home that your heating system just doesn’t seem to reach or that you want to keep a bit warmer than the rest of the house, space heaters can be an excellent option. They’re small, safe and portable and can easily keep a smaller portion of your home or room cozy and warm.

However, you’ll have to take into account the operating costs of a space heater as well as the initial investment when you’re trying to evaluate the overall cost effectiveness of this option. Most space heaters run on electricity, which often costs considerably more than oil or natural gas. If your home heating system runs on electricity anyway, this might not be so much of a factor. But if you have a gas furnace, you could wind up paying significantly more to run space heaters as supplemental heat over time.

Also, it’s worth considering that new home heating systems are likely much more energy efficient than the system you currently have in place. Although the initial installation cost can be pretty substantial, you’ll wind up saving a very large amount on your monthly heating bills by upgrading to a newer model.

Plus, you’ll be getting a system that should be able to satisfactorily heat your home without the need for space heaters or other supplemental heat sources. This translates into a pretty hefty savings over time and that’s something you’ll certainly have to take into consideration when you’re evaluating your options.

Continue Reading

Tags: , , , , , ,
Posted in Services | Comments Off on Space Heating vs. an Upgrade to Your Fountain Valley Heating System

How to Make Your Santa Ana Heating System More Effective

Wednesday, December 7th, 2011

Everyone wants an effective heating system in Santa Ana– one that will provide steady, reliable heat without you having to spend hundreds of dollars each month on gas, oil or electricity. And while the best way to improve the efficiency of your heating system in most cases is to upgrade it, there are some simple things you can do around the house to boost its effectiveness. Here are some of the best:

  • Rearrange Furniture – Just having the heat on doesn’t necessarily ensure the heat entering your room is being distributed evenly. Move your furniture in such a way that there is a clear, unimpeded path from the registers and radiators to the rest of the room. Done properly, this will make it much easier to and faster to heat every room of your house.
  • Maximize Air Flow – Air flow can be maximized in a number of ways. Make sure you close any windows near a register or radiator and that you remove any large objects that might block air flow. You should also install things that can help move air like fans and always call someone in for changes to the arrangement of your vents or radiators.
  • Clean Registers or Radiators – The cleaner your radiators or dust registers are, the more efficiently they release their heat. Not only have that, but clean radiators and registers resulted in better indoor air quality. Weekly cleaning of each room’s heating source is highly recommended.
  • Install Ceiling Fans – Ceiling fans switched to blow down are incredibly effective for distributing air throughout the room. This will keep push warm air down and keeps cold air up – in effect, reducing the need for constant running of your furnace.

Effective heating is important to keep your home comfortable, reduce the cost of heating and prolong the lifespan of your furnace . You should also make sure your heating system is properly maintained throughout the year. Skipping maintenance visits (which are highly recommended annually) will put unnecessary stress on your system and shorten its lifespan substantially, not to mention the decrease in efficiency when heating your home.

Continue Reading

Tags: , , , ,
Posted in Services | Comments Off on How to Make Your Santa Ana Heating System More Effective

How a Ceiling Fan Can Help Heat Your Home

Monday, December 5th, 2011

Most people in Silverado who have ceiling fans never turn them on in the winter. They assume that the fan is designed solely to cool the house – after all, blowing air feels pretty nice doesn’t it? But, a ceiling fan can actually help to move heat around your home and lower your heating bill if used properly. Here are some tips to do just that.

Rotating Warm Air

Warm air naturally rises. So, when you turn on your furnace and the blower fan pushes warm air through your ductwork into the various rooms of your home, the warm air immediately rises to the ceiling. So, for the room to feel as comfortable as you want it, you must wait for enough heat to circulate into the room to displace the cold air that was already there.

However, instead of waiting for warm air to fill the room, you can circulate the warm air as it arrives with a ceiling fan. By turning on your ceiling fan and changing the direction so it blows down (which most people already have it set to), the warm air will be pushed toward the floor, mixing it smoothly into the room and keeping you more comfortable without having the furnace on constantly.

This does two things. First, it keeps the room comfortable regardless of when the furnace cycles on or off. Second, it keeps the thermostat reading stable so the furnace doesn’t cycle on and off so quickly. If the warm air regularly rises up and the lower levels begin to cool, your furnace will frequently turn on and off as it tries to maintain the same temperature.

A Low Cost Addition to Your Home

Ceiling fans are inexpensive and aesthetically pleasing. They move air throughout the room, keep warmth low where you need it and can help reduce your energy bill in multiple ways. If you’re not sure whether a ceiling fan is right for you, talk to a Silverado technician about just how much money one of these simple devices can save you. I bet you’ll be convinced.

Continue Reading

Tags: , , , , , ,
Posted in Services | Comments Off on How a Ceiling Fan Can Help Heat Your Home